The Mako® Hotend is a precision-engineered 48W upgrade for Bambu Lab X1 and P1 printers, built to deliver faster, cleaner, and more reliable printing. With its quick-swap nozzle design and Bimetallic Heat Break™ technology, Mako makes nozzle changes effortless while unlocking up to 60% faster print speeds than the stock setup — with a hotend rated to 400 °C. Your X1 / P1 firmware still caps the nozzle at 300 °C, so the Mako always runs well inside its limit.
Which Mako is this?
This is the original 48W Mako, the version that ships with the Heater Adapter, letting it run with a printer-specific heater. Slice also make a newer 65W High-Power Mako — a different product with a full-footprint heater and no adapter.
The two differ in heater and rating: the 65W prints faster and is rated to 360 °C, this original 48W to 400 °C. On an X1 or P1 that difference is headroom, not a longer material list — the printer's firmware stops the nozzle at 300 °C either way. PC, PA and CF/GF blends that print at or below 300 °C are in reach; PPS-CF, PEEK and PEKK need a printer that can actually reach their temperatures.
Before You Buy — the Mako takes FIN nozzles only
The Mako uses the FIN standard (Free and open-source Insulated Nozzle). FIN evolved from RepRap V6, but the tip interlocks with the silicone boot to insulate the hotend — so it is not backward compatible.
Standard M6 / RepRap (V6) nozzles will not work in the Mako, including our RepRap GammaMaster® and the M6 nozzles sold for the TZ-3.0.
Features
-
Rated to 400 °C: Runs far inside its limit at the X1 / P1's 300 °C maximum, with 40 °C more rating than the newer 65W Mako.
-
Effortless Nozzle Swaps: Change nozzles in seconds with the Mako’s quick-release design — no tools, no downtime.
-
Up to 60% Faster Printing: Optimized heat flow and superior thermal management push the limits of your printer’s speed without compromising quality.
-
Bimetallic Heat Break™: Prevents jams, reduces heat creep, and ensures consistent filament flow — even with flexible or abrasive materials.
-
Broad Filament Compatibility: Handles everything from soft TPU to reinforced carbon fiber and glass-filled filaments with ease.
Which Variant Should I Pick?
Every variant is the same Mako hardware — the only difference is the FIN tip that comes pre-installed. Pick the tip that matches what you print; you are not choosing a different hotend.
-
GammaMaster (FIN): Durable, abrasion-resistant nozzle for carbon and glass fiber filaments.
-
CHT (FIN): Boosts flow rate and layer bonding by splitting filament into three strands for faster, stronger prints.
-
DiamondBack (FIN): Features a solid diamond tip for unmatched durability and precision — built to last a lifetime.
⚙️ Tip: The CHT FIN nozzle is sensitive to over-torque. Do not exceed 1.5 Nm — use the Slice Nozzle Torque Wrench™ for safe installation.
Specifications
| Feature |
Specification |
| Version |
Original Mako, 48W — includes the Heater Adapter |
| Max Temperature |
400 °C rated (X1 / P1 firmware max: 300 °C) |
| Speed |
Up to 60% faster than stock |
| Nozzle Standard |
FIN — not compatible with M6 / RepRap (V6) |
| Heat Break |
Bimetallic Heat Break™ |
| Fan |
High-Performance Aluminium |
| Thermal Interface |
Thin Film Thermal Grease, pre-applied |
Package Includes
- 1 × Mako® Hotend for Bambu Lab
- 1 × FIN Nozzle 0.4 mm — in the geometry you select above
- 1 × Mako Silicone Boot
- 1 × Mako Retaining Clip
- 1 × Mako Air Dam — blocks part-cooling air from reaching the hot block, so your temperatures stay stable
- 1 × Heater Adapter — lets the Mako run with a printer-specific heater
- Thin Film Thermal Grease (applied to the assembled hotend)
- 1 × Electronics Kit — Heater, Sensor and High-Performance Aluminium Fan